# Best answer: How much is a ton of gravel cost UK?

Contents

## How much area does a ton of 20mm gravel cover?

Based on our 20mm sized stones, 1 bulk bag of gravel will cover approximately 12 sqm at 50mm depth for paths and driveways. Alternatively, 1 bulk bag will cover approximately 16 sqm at 30mm depth. Our 25kg Polybags will roughly cover 0.4sqm.

## How many square meters does a ton of gravel cover?

Type 3 Aggregate Calculator

Un-compacted Cloburn aggregates weigh 1.4 tonnes per cubic metre. Therefore if you wish to apply them at a 50mm depth (the normal depth for a driveway) one tonne will cover 14 square metres.

## How many square feet will 5 tons of gravel cover?

Regarding this, “how much area does 5 tons of gravel cover?, typically, as 1 ton of gravel cover around 108 sq ft area for 2 inch depth, so 5 tons of gravel = 108 × 5 = 540 sf coverage, therefore 5 tons of gravel can cover around 540 square feet or 60 square yards or 50 square meters area for standard 2 inch depth.

## How much does gravel cost UK?

On average, gravel works out at about £74 per tonne, or £60 per 850kg bag. Fortunately, it’s possible to lay a large gravel driveway in one piece, unlike concrete or tarmac.

## What area will a 25kg bag of gravel cover?

For Decorative Gravel

As a rule of thumb 1 of our 25kg bags will cover an area of 0.25m to a recommended depth of 50mm.

## How much gravel do I need for my driveway UK?

What depth of gravel do I need? You would usually lay a 10mm aggregate at a depth of 30-40mm, but on a driveway this would need to be at least 50mm. A 20mm aggregate would need to be at least 40-50mm deep, and at least 50-60mm on driveways. A larger aggregate will settle and bond together better than smaller ones.

## How far does a ton of gravel spread?

Understanding Size and Coverage

Using 2 inches for the depth, the following measurements are a guide to the amount of gravel coverage per ton: 1/4 to 1/2 inch gravel, 100 square feet per ton; 1/2 to 1 inch gravel, 90 square feet per ton; and 1 1/2 to 2 inches gravel, 80 square feet per ton.

## How do I calculate how much gravel I need?

Length in feet x Width in feet x Depth in feet (inches divided by 12). Take the total and divide by 21.6 (the amount of cubic feet in a ton). The final figure will be the estimated amount of tons required.

## How deep should I lay gravel?

Decorative aggregates should be laid at a depth of 50mm. This ensures proper coverage without revealing the surface below. Laying the gravel too deep will mean you sink into the surface and it becomes difficult to walk across.

IT IS AMAZING:  Can I take a year off university UK?

## How big is a ton of gravel?

How much is a ton of gravel? A ton of gravel with average-sized pebbles is about 0.705 cubic yards, or 19 cubic feet, assuming it has been screened for debris and contains no leftover dirt, sand, etc.

## How deep should my gravel driveway be?

Driveway Layers

A gravel drive should have a first layer of baseball-sized stones at least 4 inches deep. According to Tim Carter of AskTheBuilder.com, each layer thereafter should be 4 inches thick and in gradually smaller stone.

## How much is a Type 2 Cover ton?

Regarding this, how many square yard does 2 tons of gravel cover? according to Imperial or US customary measurement system, in general, 2 tons of gravel can be sufficient to cover approx 24 square yards for 2 inch depth of construction project like roadways, pedestrian or others structure.

## How much gravel do I need for a 2 car driveway?

2. Decide on the depth of the rock you are purchasing. According to the Home Depot, 4 to 6 inches of rock or gravel is needed for a driveway.

## Can you put gravel over tarmac?

Yes, you can. Nidagravel gravel grids are the ideal way to stabilise gravel that is to be laid directly over concrete, tarmac and block paved driveways. In fact, a gravel grid is the only way you can install gravel successfully over a solid slab.